How to String a Weed Eater With Two Holes

Are you planning to trim your weed plants? There is no better tool than a weed eater. It is perfectly designed to cater to areas, like lawn edges or around trees, that a lawnmower may fail to reach.

However, you need to know a few things before using a weed eater. You must know how to string a weed eater with two holes and how to achieve the best results from your efforts. This could be tricky, and it is best to find the details.

Read now to learn everything you need to know.

What is a Weed Eater?

A weed eater, also known as a trimmer, strimmer, or whacker, is a garden tool for trimming weeds, grass, or other plants. It is a great alternative to a lawnmower, especially for reaching unreachable areas.

Some of the common features found in a weed eater are:

• Spinning Plastic Line: This part helps cut through vegetation like a sharp blade.
• Motor: Every weed eater has a motor that can be powered by gas, battery, or electricity, depending on the model chosen. If you have tough weeds to handle, it is best to get gas-powered weed eaters as they are quite powerful.
• Handle: Weed eaters have a shaft and a handle at the end. This is a common feature that allows you to take full control of the weed eater.

Weed eaters are designed for precision trimming, so having one is necessary to grow healthy weeds. However, using it requires some technique.

How to String a Weed Eater With Two Holes- A Step-By-Step Guide

Stringing a weed eater with two holes in a spool isn’t a tough job. In fact, you can perform this task using the following steps.

1. Start with switching off your weed eater completely. Make sure that it isn’t attached to any power source.
2. Now, remove the spool from the machine’s head. This is easily achieved by pressing certain tabs to unscrew the part. You can read the manual to learn.
3. The spool has two holes. These help secure the trimmer line’s ends.
4. Take your trimmer line and cut it into two pieces. Typically, make each piece 10 to 15 feet long. However, you may want to check the manual to confirm.
5. Now, insert one end of a line into the hole. Adjust it so that you have an equal amount of the line on both sides. Repeat the same for the other piece as well.
6. Look at the arrows on your spool. Follow their direction to wind the lines. Do this process with precision. Avoid any sort of overlapping.
7. Now secure the line with notches. It is important to hold your line safely in one position.
8. Once done, carefully place the spool back in the head.
9. Reattach the head to the machine.
10. Test the weed eater by switching it on. Check if the line feeds effortlessly or if you require further work on this task.

If you cannot understand the steps, you can always search for the technique online. There are plenty of YouTube videos available to help you out.

Alternatively, you can get help from an expert to do the job. It won’t take much time, but with guidance, the trimming results are usually remarkable.

How to String a Weed Eater With Two Holes: Mistakes to Avoid

To eliminate any glitch or poor performance when stringing your weed eater with two holes, here are some mistakes to avoid as a precaution.

Use an Inappropriate Size Line

Your line shouldn’t be too thick or thin for your weed eater. It must be of the same size as mentioned in the manual. If it isn’t, you may damage your tool or get poor-cutting results.

Wind the Line In the Wrong Direction

This is a common mistake. Many people take the winding step for granted. However, incorrect lines prevent the feeding procedure.

In most cases, the direction of the arrows is counterclockwise. However, check and confirm before completing this step.

Winding the Line Loosely or Incorrectly

Winding the line loosely can tangle the lines, leading to feeding problems. To prevent that, make sure that your lines are winded tightly. This should also not overlap.

Take additional help if you can’t achieve it alone.

Cut the Line Much Shorter than Required

This is another mistake many people make without knowing the output. Short lines reduce the efficiency of cutting. Besides, this problem leads to frequent reloading, which is a lot of hassle.

Securing the Lines Inappropriately

This process requires a lot of patience. You need to spend enough time to secure your lines appropriately via notches. If you don’t, the lines will unwind and will create havoc.

Overfill the Spool with Lines

You may be tempted to put too many lines in the spool, but it will just cause the machine to jam. Your line won’t advance properly. Plus, you may witness inefficient cutting.

To avoid all of this and more, check the manual and only use the recommended amount of line as mentioned by the manufacturers.

Opt for Old Lines

This mistake should also be avoided at all costs. Instead of using an old line to save money, use a new one. Old lines are usually brittle and weak, allowing them to break easily.

Wrapping Up

A weed eater is a savior, especially when trimming weed plants that a simple lawnmower can’t reach. The machine is also quite powerful and makes your work easy and quick.

However, if you use this tool for the first time, you may not know how to string a weed eater with two holes. Hopefully, this article has helped you do that seamlessly now. Just follow the steps and avoid the mistakes mentioned above.

Trim your weed nicely so it can grow to give you the comfort you need.